-
摘要: 采用粉末冶金技术制备了SiCp/Al复合材料,探讨了SiC颗粒质量分数对SiCp/Al复合材料密度、布氏硬度、微观形貌以及摩擦磨损性能的影响。结果表明,SiC颗粒表面形成了少量可提高界面结合性的Al4C3化合物。随着SiC质量分数增加,SiCp/Al复合材料的密度没有明显的变化,当SiC质量分数增加至25%时,密度明显下降。SiCp/Al复合材料的布氏硬度随着SiC质量分数的增加呈先增长后减小的变化趋势。当SiC质量分数为20%时,材料的硬度最优(HBW 114),平均摩擦系数达到最大值(0.3425),摩擦后试样表面形貌平整且犁沟较浅,SiC颗粒未出现明显剥落。Abstract: The SiCp/Al composites were prepared by the powder metallurgy technology, and the influences of SiC particle mass fraction on the density, Brinell hardness, microstructure, friction, and wear of the SiCp/Al composites were investigated. The results show that, a small amount of Al4C3 compounds can be formed on the surface of SiC particles, improving the bonding properties. With the increase of SiC mass fraction, the density of the SiCp/Al composites has no obvious change, when the SiC mass fraction increases to 25%, the density decreases obviously. The Brinell hardness of the SiCp/Al composites increases first and then decreases with the increase of SiC mass fraction. When SiC mass fraction is 20%, the optimal Brinell hardness is HBW 114 and the average friction coefficient can reach to the maximum as 0.3425, the surface morphology after friction is flat and shallow furrows, and the SiC particles has not obvious spalling.
-
Key words:
- SiC particles /
- SiCp/Al composites /
- density /
- hardness /
- friction /
- wear
-
表 1 SiCp/Al复合材料的配比组成(质量分数)
Table 1. Composition of the SiCp/Al samples
% 试样 Al Cu Si Mn SiC Mg 1# 70 10 8 1.5 10 0.5 2# 65 10 8 1.5 15 0.5 3# 60 10 8 1.5 20 0.5 4# 55 10 8 1.5 25 0.5 -
[1] Qiao W M, Li Y. Preparation process and application of aluminum matrix composites. Hot Working Technol, 2013, 42(4): 126乔文明, 李颖. 铝基复合材料的制备及应用. 热加工工艺, 2013, 42(4): 126 [2] Jung S W, Lee J H, Nam J B, et al. Analysis of strengthening mechanism in hybrid short fiber/particle reinforced metal matrix composites. Key Eng Mater, 2000, 183: 1297 [3] Gao H X, Chen B L, Fan J L, et al. Study on microstructure and properties of SiC particle-reinforced wear resistant aluminum matrix composites. Hot Working Technol, 2018, 47(8): 93高红霞, 陈宝龙, 樊江磊, 等. SiC颗粒增强耐磨铝基复合材料组织及性能研究. 热加工工艺, 2018, 47(8): 93 [4] Cui Y. Aerospace application of silicon carbide particulate reinforced aluminum matrix composites. J Mater Eng, 2003(6): 3 doi: 10.3969/j.issn.1001-4381.2003.06.001崔岩. 碳化硅颗粒增强铝基复合材料的航空航天应用. 材料工程, 2003(6): 3 doi: 10.3969/j.issn.1001-4381.2003.06.001 [5] Ping Y L, Jia C C, Qu X H, et al. Present state of research methods for the SiCp/Al composites. Powder Metall Technol, 2005, 23(4): 296 doi: 10.3321/j.issn:1001-3784.2005.04.012平延磊, 贾成厂, 曲选辉, 等. SiCp/Al复合材料的研究方法现状. 粉末冶金技术, 2005, 23(4): 296 doi: 10.3321/j.issn:1001-3784.2005.04.012 [6] Chu K, Jia C C, Yin F Z, et al. Fabrication on electronic package box of SiCp/Al composites with high volume fraction of SiCp. Acta Mater Compos Sin, 2006, 23(6): 108 doi: 10.3321/j.issn:1000-3851.2006.06.018褚克, 贾成厂, 尹法章, 等. 高体积分数SiCp/Al复合材料电子封装盒体的制备. 复合材料学报, 2006, 23(6): 108 doi: 10.3321/j.issn:1000-3851.2006.06.018 [7] Zheng J, Jia Z H, Ma G. Progress in research of SiC particle reinforced Al-based composites. Titanium Ind Prog, 2006, 23(6): 13 doi: 10.3969/j.issn.1009-9964.2006.06.005郑晶, 贾志华, 马光. 碳化硅颗粒增强铝基复合材料的研究进展. 钛工业进展, 2006, 23(6): 13 doi: 10.3969/j.issn.1009-9964.2006.06.005 [8] Fan J Z, Yao Z K, Li Y C, et al. The progress in the research of particulate-reinforced aluminum matrix composites. Mater Rev, 1997, 11(3): 48樊建中, 姚忠凯, 李义春, 等. 颗粒增强铝基复合材料的研究进展. 材料导报, 1997, 11(3): 48 [9] Chu K, Jia C C, Liang X B, et al. Fabrication of SiCp/Al composites with high volume fraction SiCp by PIM and pressure infiltration. Powder Metall Technol, 2007, 25(5): 348褚克, 贾成厂, 梁雪冰, 等. 注射成形与压力熔渗方法制备高体积分数SiCP/Al封装盒体及其导热性能分析. 粉末冶金技术, 2007, 25(5): 348 [10] Guo M H, Liu J Y, Jia C C, et al. Microstructure and properties of SiCp/Al electronic packaging materials fabricated by pseudo-semi-solid thixoforming. J Univ Sci Technol Beijing, 2014, 36(4): 489郭明海, 刘俊友, 贾成厂, 等. 伪半固态触变成形制备SiCp/Al电子封装材料的组织与性能. 北京科技大学学报, 2014, 36(4): 489 [11] Feng S Q, Li J Y, Su L, et al. Theoretical study on hardness characteristics of super hard materials under high pressure // Proceedings of the 18th Chinese High Pressure Science Conference. Chengdu, 2016: 282冯世全, 李俊玉, 苏磊, 等. 高压下超硬材料硬度特性的理论研究//第十八届中国高压科学学术会议文集. 成都, 2016: 282 [12] Chen C C, Chen G, Yan H G, et al. Friction and wear properties of particle reinforced graded aluminum matrix composites. Chin J Nonferrous Met, 2011, 21(6): 1258陈聪聪, 陈刚, 严红革, 等. 颗粒增强铝基梯度复合材料的摩擦磨损性能. 有色金属学报, 2011, 21(6): 1258