-
摘要: 通过研究金属钼(Mo)在真空环境下蒸发速率和饱和蒸气压与温度的关系,探讨了蓝宝石单晶炉Mo隔热屏内胆的损坏机理。结果表明,蓝宝石单晶炉的核心工作温度在2100 ℃以上,每炉的高温阶段时间超过120 h,隔热屏内胆在高真空环境下产生蒸发,由电子显微结构可以看到Mo片表面疏松、多孔,厚度逐渐变薄、剥落,失去隔热作用。利用金属高温环境下的蒸发速率、饱和蒸气压和工作时间推算出金属因蒸发而造成的厚度变化公式,由公式测算出来蓝宝石单晶炉的隔热屏内胆变薄的趋势与实际使用寿命相吻合。由于金属钨(W)的熔点比钼更高,利用该公式可以测算出W在蓝宝石单晶炉最严苛的工作条件下几乎不会蒸发变薄,是一种理想的隔热屏内胆替代品。Abstract: The relationships of the evaporation rate, the saturated vapor pressure, and the working temperature of Mo in vacuum environment were investigated, and the damage mechanism of Mo inner heat shield in sapphire single crystal furnace was discussed. In the results, the core operating temperature of the sapphire single crystal furnace is above 2100 ℃, the high temperature period of each cycle is more than 120 h, and the inner heat shield evaporates in the high vacuum environment. It can be seen from the microstructure that the surface of Mo sheet is loose and porous, and the sheet thickness gradually becomes thin and peels off, losing the heat insulation effect. The formula of the thickness change due to the metal evaporation is deduced from the evaporation rate, the saturated vapor pressure, and the working time at high temperatures. The thickness change trend on the inner heat shield of sapphire single crystal furnace calculated by the formula coincides with the actual service life. Since the melting point of W metal is higher than that of Mo metal, it will hardly evaporate and become thinner under the most severe working conditions in the sapphire crystal furnace according to the calculation results by the formula. Therefore, W is an ideal substitute of the inner heat shield.
-
Key words:
- sapphire /
- heat shield /
- molybdenum /
- vacuum /
- evaporate
-
表 1 不同温度下Mo和W的饱和蒸气压与蒸发速率
Table 1. Vapour pressure and evaporation rate of the molybdenum and tungsten at different temperatures
温度 / ℃ 饱和蒸气压 / Pa 蒸发速率 / (mg·cm−2·h−1) Mo W Mo W 1700 2×10−5 10−10 0.003 — 1800 1×10−4 2×10−9 0.020 6×10−7 1900 6×10−4 2×10−8 0.200 6×10−6 2000 0.003 2×10−7 0.800 6×10−5 2100 0.010 1×10−6 2.000 4×10−4 2200 0.030 6×10−6 5.000 0.002 2300 0.100 3×10−5 40.000 0.010 表 2 蓝宝石长晶炉内胆Mo片厚度测量结果
Table 2. Measurement results of the Mo sheet thickness in the sapphire single crystal furnace
cm 测量点 长晶炉数 原始厚度 1 2 3 4 5 测量点1 2.02 1.80 1.59 1.36 1.10 0.90 测量点2 2.04 1.83 1.60 1.36 1.09 0.88 测量点3 2.04 1.82 1.63 1.38 1.13 0.91 -
[1] Wang R G, Chen Z Q, Hu G Y. The comparison of LED dedding materials SiC, ZnO, Al2O3. Sci Technol Eng, 2006, 6(2): 121 doi: 10.3969/j.issn.1671-1815.2006.02.005王如刚, 陈振强, 胡国永. 几种LED衬底材料的特征对比与研究现状. 科学技术与工程, 2006, 6(2): 121 doi: 10.3969/j.issn.1671-1815.2006.02.005 [2] Li J Q, Su X P, Na Mu J L T, et al. Research trends and current status in producing sapphire domes. J Synth Cryst, 2007, 36(2): 467 doi: 10.3969/j.issn.1000-985X.2007.02.049李金权, 苏小平, 那木吉拉图, 等. 蓝宝石整流罩的研制现状与发展趋势. 人工晶体学报, 2007, 36(2): 467 doi: 10.3969/j.issn.1000-985X.2007.02.049 [3] Nie H, Lu B Z. Sapphire window and it’ s application in military electro-optical equipment. Ship Electron Eng, 2005, 25(2): 131 doi: 10.3969/j.issn.1627-9730.2005.02.035聂辉, 陆炳哲. 蓝宝石及其在军用光电设备上的应用. 舰船电子工程, 2005, 25(2): 131 doi: 10.3969/j.issn.1627-9730.2005.02.035 [4] Fan Z G, Liu J J, Xiao H S, et al. Research progress on growth technique and application of sapphire single crysta. J Chin Ceram Soc, 2011, 39(5): 880范志刚, 刘建军, 肖昊苏, 等. 蓝宝石单晶的生长技术及应用研究进展. 硅酸盐学报, 2011, 39(5): 880 [5] Yang Y H, Li J, Wang C C, et al. Effect of the heat-shield spacing on the crystal growth of Kyropoulos sapphire. J Synth Cryst, 2017, 46(8): 1430杨轶涵, 李进, 王长春, 等. 热屏间距对泡生法蓝宝石单晶生长影响研究. 人工晶体学报, 2017, 46(8): 1430 [6] Zuo H B, Yang X H, Song B, et al. Single Crystal Furnace Body for Growth of Big Sapphire with Size over 300 mm: China Patent, CN200920100239.0. 2010-02-24左洪波, 杨鑫宏, 宋波, 等. 一种用于生长300 mm以上大尺寸蓝宝石的单晶炉炉体: 中国专利, CN200920100239.0. 2010-02-24 [7] Cheng G, Meng X Q, Dong S. Broken inner heat insulation screen of Kyropoulos sappire crystal grower. Rare Met Mater Eng, 2013, 42(Sppl 2): 517承刚, 孟秀清, 董珊. 泡生法蓝宝石晶体炉内隔热屏损坏机理研究. 稀有金属材料与工程, 2013, 42 (增刊2): 517 [8] Xiao X. Research of Controllable Thermal Field of 60 kg-Grade Kyropoulos-Method Sapphire Furnace [Dissertation]. Hangzhou: Zhejiang Sci-Tech University, 2016肖雄. 泡生法蓝宝石60 kg级生长炉可控温场研究[学位论文]. 杭州: 浙江理工大学, 2016 [9] Yu H Q, Xu Y L, Shi H B, et al. Experiment research on adhesive crucible phenomenon with sapphire crystal growth. J Synth Cryst, 2012, 41(6): 1675 doi: 10.3969/j.issn.1000-985X.2012.06.037于海群, 徐永亮, 施海滨, 等. 蓝宝石晶体生长过程中粘锅现象的实验研究. 人工晶体学报, 2012, 41(6): 1675 doi: 10.3969/j.issn.1000-985X.2012.06.037 [10] Deng Y. Study on the Preparation of High-Pure Indium [Dissertation]. Kunming: Kunming University of Science and Technology, 2007邓勇. 高纯金属铟的制备研究[学位论文]. 昆明: 昆明理工大学, 2007 [11] Qiu K Q, Duan W J, Chen Q Y. Rate of metal evaporation under vacuum condition. Nonferrous Met, 2002, 54(2): 48丘克强, 段文军, 陈启元. 金属在真空状态下的蒸发速率. 有色金属, 2002, 54(2): 48 [12] Dai Y N, Xia D K, Chen Y, et al. Evaporation of metals in vacuum. J Kunming Inst Technol, 1994, 19(6): 26戴永年, 夏丹葵, 陈燕, 等. 金属在真空中的挥发性. 昆明工学院学报, 1994, 19(6): 26 [13] Zhou Z, Ding P D. Volatilization mechanism of magnesium in directed metal oxidation. Chin J Nonferrous Met, 2002, 12(Suppl 1): 210周正, 丁培道. 金属直接氧化过程中的镁挥发机制. 中国有色金属学报, 2002, 12(增刊 1): 210 [14] Guo L, Deng Z N, Jin B, et al. Roll-smoothing annealing process of high precision tungsten sheet. Cement Carb, 2011, 28(1): 34 doi: 10.3969/j.issn.1003-7292.2011.01.007郭磊, 邓自南, 金波, 等. 高精度钨片校平退火工艺研究. 硬质合金, 2011, 28(1): 34 doi: 10.3969/j.issn.1003-7292.2011.01.007 [15] Chen J, Xiong N, Ge Q L, et al. Manufacturing technology of tungsten crucibles. China Tungsten Ind, 2016, 31(1): 63 doi: 10.3969/j.issn.1009-0622.2016.01.012陈锦, 熊宁, 葛启录, 等. 钨坩埚的制备技术. 中国钨业, 2016, 31(1): 63 doi: 10.3969/j.issn.1009-0622.2016.01.012