| Citation: |
HUANG Lirong, WANG Yun, XIE Junjie, HUANG Bihua. Pressing the coarse-grained WC−10Co cemented carbide assisted by ultrasonic vibration[J]. Powder Metallurgy Technology, 2023, 41(6): 586-592. DOI: 10.19591/j.cnki.cn11-1974/tf.2022030005
|
The suppression technology assisted by longitudinal ultrasonic vibration was proposed to solve the problems of poor powder fluidity, uneven particle size distribution, and poor mechanical properties for the coarse-grained WC−10Co cemented carbides. The effects of compression force, height-diameter ratio, ultrasonic time of preloading, and ultrasonic amplitude on the compact density, compact surface quality, and mechanical properties of the alloys were discussed. The results show that, compared with the conventional pressing, the powder particles have the violent collision under the effect of ultrasonic vibration, enhancing the fluidity between particles. The density increases with the pressing force increase from 80 to 100 MPa. The compact density increases significantly, when the height-diameter ratio reduces, the ultrasonic time of preloading increases, and the ultrasonic amplitude increases. At the same time, the surface quality of the compacts is improved, and the elastic aftereffect is decreased by 0.16%. The pores of the alloys are reduced, the grain size is evenly distributed, and the coarse grain is reduced after sintering. With the little change in hardness and density, the fracture toughness increases by 5.83%~16.10%, while the bending strength decreases obviously.
| [1] |
高德强, 刘雪梅, 冯浩, 等. 超粗晶WC−8Co硬质合金循环压缩过程中组织演变的研究. 中国体视学与图像分析, 2020, 25(2): 135
Gao D Q, Liu X M, Feng H, et al. Study on microstructure evolution of ultra coarse-grained WC−8Co cemented carbide during cyclic compression. Chin J Stereol Image Anal, 2020, 25(2): 135
|
| [2] |
He R, Li B, Ou P, et al. Effects of ultrafine WC on the densification behavior and microstructural evolution of coarse-grained WC−5Co cemented carbides. Ceram Int, 2020, 46(8): 12852 DOI: 10.1016/j.ceramint.2020.01.113
|
| [3] |
Cao R J, Lin C G, Xie X C, et al. Microstructure and mechanical properties of WC−Co-based cemented carbide with bimodal WC grain size distribution. Rare Met, 2023, 42(8): 2809 DOI: 10.1007/s12598-018-1025-y
|
| [4] |
徐伟, 陈玉柏, 汤昌仁, 等. 高性能非均匀结构硬质合金的制备及其形成机理研究. 中国钨业, 2021, 36(1): 48 DOI: 10.3969/j.issn.1009-0622.2021.01.008
Xu W, Chen Y B, Tang C R, et al. Preparation and formation mechanism of high performance cemented carbide with non-uniform structure. China Tungsten Ind, 2021, 36(1): 48 DOI: 10.3969/j.issn.1009-0622.2021.01.008
|
| [5] |
Ignatieva L N, Zverev G A, Adamenko N A, et al. Peculiarities of the structure of copper- and nickel-fluoropolymer composites fabricated by explosive pressing. J Fluorine Chem, 2015, 172: 68 DOI: 10.1016/j.jfluchem.2015.02.002
|
| [6] |
Asnaashari S, Ghambari M. Preparation and characterization of composite WC/Co through rapid omnidirectional compaction. J Alloys Compd, 2020, 859: 157764
|
| [7] |
Cao S H, Huang B Y, Qu X H, et al. Densification mechanism of warm compaction and powder mixture designing rules. J Cent South Univ Technol, 2000, 7(1): 4 DOI: 10.1007/s11771-000-0002-3
|
| [8] |
Wang X, Qi Z, Chen W. Study on constitutive behavior of Ti−45Nb alloy under transversal ultrasonic vibration-assisted compression. Arch Civ Mech Eng, 2021, 21(1): 1 DOI: 10.1007/s43452-020-00148-5
|
| [9] |
Bagherzadeh S, Abrinia K, Han Q. Analysis of plastic deformation behavior of ultrafine-grained aluminum processed by the newly developed ultrasonic vibration enhanced ECAP: Simulation and experiments. J Manuf Processes, 2020, 50: 485 DOI: 10.1016/j.jmapro.2020.01.010
|
| [10] |
Du K, Huang J, Chen J, et al. Mechanical property and structure of polypropylene/aluminum alloy hybrid prepared via ultrasound-assisted hot-pressing technology. Materials, 2020, 13(1): 236 DOI: 10.3390/ma13010236
|
| [11] |
Lin J, Li J, Liu T, et al. Evaluation of friction reduction and frictionless stress in ultrasonic vibration forming process. J Mater Process Technol, 2021, 288(7): 116881
|
| [12] |
Lv K, Yang K, Zhou B, et al. The densification and mechanical behaviors of large-diameter polymer-bonded explosives processed by ultrasonic-assisted powder compaction. Mater Des, 2021, 207: 109872 DOI: 10.1016/j.matdes.2021.109872
|
| [13] |
赵艳波, 马麟, 刘波, 等. 基于离散元法的纯铁粉振动填充密度分析. 粉末冶金技术, 2020, 38(6): 429 DOI: 10.19591/j.cnki.cn11-1974/tf.2019070006
Zhao Y B, Ma L, Liu B, et al. Analysis of vibration filling density of pure iron powder based on discrete element method. Powder Metall Technol, 2020, 38(6): 429 DOI: 10.19591/j.cnki.cn11-1974/tf.2019070006
|
| [14] |
王海陆, 刘军, 林立, 等. 基于离散元的不同粒径配比粉末压制相对密度与力链分析. 粉末冶金技术, 2021, 39(6): 490 DOI: 10.19591/j.cnki.cn11-1974/tf.2019120014
Wang H L, Liu J, Lin L, et al. Analysis of relative density and force chain of powder with different particle size ratio based on discrete element method. Powder Metall Technol, 2021, 39(6): 490 DOI: 10.19591/j.cnki.cn11-1974/tf.2019120014
|
| [15] |
蒋煜, 李旭东. 粉末压制成形的细观模拟分析. 甘肃科学学报, 2020, 32(5): 56 DOI: 10.16468/j.cnki.issn1004-0366.2020.05.012
Jiang Y, Li X D. Meso simulation analysis of powder pressing. J Gansu Sci, 2020, 32(5): 56 DOI: 10.16468/j.cnki.issn1004-0366.2020.05.012
|
| [16] |
陈楚轩. 硬质合金质量控制原理. 株洲: 中国钨业协会硬质合金分会, 2007
Chen C X. Quality Control Principle of Cemented Carbide. Zhuzhou: Cemented Carbide Branch of China Tungsten Industry Association, 2007
|
| [17] |
Sedaghat H, Xu W, Zhang L. Ultrasonic vibration-assisted metal forming: Constitutive modelling of acoustoplasticity and applications. J Mater Process Technol, 2019, 265: 122 DOI: 10.1016/j.jmatprotec.2018.10.012
|
| [18] |
朱骥飞, 张立, 徐涛, 等. 基于Image J软件的硬质合金显微组织参数化定量分析. 粉末冶金材料科学与工程, 2015, 20(1): 26
Zhu J F, Zhang L, Xu T, et al. Parametric quantitative analysis of cemented carbide microstructure based on Image J software. Mater Sci Eng Powder Metall, 2015, 20(1): 26
|
| [19] |
冯志, 程登峰, 黎明华, 等. 碳化配碳量对粗颗粒WC粉末形貌及WC−8%Co合金性能的影响. 硬质合金, 2021, 38(3): 171
Feng Z, Cheng D F, Li M H, et al. Effect of carbon content on morphology of coarse WC powder and properties of WC−8% Co alloy. Cement Carb, 2021, 38(3): 171
|
| [1] | GAO Jiaojiao, PING Ping, HU Shiheng, SONG Jinpeng. Effect of sintering temperature on microstructure and mechanical properties of Ti(C,N)-HfN/Ti(C,N)-WC laminated ceramics[J]. Powder Metallurgy Technology, 2024, 42(2): 115-121. DOI: 10.19591/j.cnki.cn11-1974/tf.2023040006 |
| [2] | GAO Jiaojiao, PING Ping, LIU Jiabao, SONG Jinpeng. Effect of Re content on microstructure and mechanical properties of TiCN–WC–HfN ceramics[J]. Powder Metallurgy Technology, 2024, 42(1): 53-58. DOI: 10.19591/j.cnki.cn11-1974/tf.2023040001 |
| [3] | HAN Guoqiang, WANG Weiwei, LI Xiaoyan. Effect of powder sintering on microstructure and mechanical properties of magnesium‒scandium alloys[J]. Powder Metallurgy Technology, 2023, 41(6): 548-553. DOI: 10.19591/j.cnki.cn11-1974/tf.2020070005 |
| [4] | ZHAO Gang, ZHOU Xiao-jun, LIANG Bin, BAI Xiao-dong, CAI Zhen-yang, YANG Sheng-chun. Effect of silicide coating on mechanical properties of Nb‒Ti‒Al alloys[J]. Powder Metallurgy Technology, 2022, 40(6): 494-498. DOI: 10.19591/j.cnki.cn11-1974/tf.2020120004 |
| [5] | LI Shang-jie, YANG Hua. Effect of cobalt concentration gradient by infiltration sintering on the mechanical properties of polycrystalline diamond compacts[J]. Powder Metallurgy Technology, 2021, 39(6): 526-531. DOI: 10.19591/j.cnki.cn11-1974/tf.2021090014 |
| [6] | WEI Zi-chen, ZHANG Lin, QIN Ming-li, LI Xing-yu, QUE Zhong-you, QU Xuan-hui. Effect of powder size on microstructure and mechanical properties of rhenium[J]. Powder Metallurgy Technology, 2021, 39(3): 196-202. DOI: 10.19591/j.cnki.cn11-1974/tf.2021030014 |
| [7] | ZHANG Cheng-gong, FAN Jing-lian, CHENG Hui-chao. Effects of W content by mass on the microstructure and mechanical properties of Mo-W alloy[J]. Powder Metallurgy Technology, 2020, 38(1): 18-24. DOI: 10.19591/j.cnki.cn11-1974/tf.2020.01.003 |
| [8] | LIU Ren-zhi, AN Geng, YANG Qin-li, ZHUANG Fei, WANG Yin-ting, CUI Yu-qing, WANG Na, CAO Wei-cheng. Microstructures and mechanical properties of Mo-Re-La alloy[J]. Powder Metallurgy Technology, 2018, 36(6): 429-432,444. DOI: 10.19591/j.cnki.cn11-1974/tf.2018.06.005 |
| [9] | Tong Guoquan, Wang Erde, He Shaoyuan. THE INFLUENCE OF THE BINDER COMPOSITION ON THE MICROSTRUCTURES AND MECHANICAL PROPERTIES OF WC-20(Fe/Co/Ni) CEMENTED CARBIDES[J]. Powder Metallurgy Technology, 1995, 13(4): 243-248. |
| [10] | Li Yulong, Guan Qingfeng, Guo Zuoxing, Hu Jiandong, Wang Hongying, Wang Yufen. STRUCTURES AND PROPERTIES OF P/M COMPACTS AFTER LASER BULK SINTERING[J]. Powder Metallurgy Technology, 1995, 13(3): 192-195. |
| 1. |
钟韬，郭荣臻，林晓川，柳龙婷，王佳鑫，徐志强，郭世柏. 等离子烧结工艺对WC/Cr_3C_2/La_2O_3刀具材料力学性能的影响. 粉末冶金技术. 2024(06): 582-588 .
 本站查看
|
Supported by: Beijing Renhe Information Technology Co., Ltd. 
DownLoad: