AdvancedSearch
DING Xiaolong, YANG Zhaofang, ZHENG Hejing. Effect of ZrP on properties of CuBi-steel-backed double-layer metal composites[J]. Powder Metallurgy Technology, 2024, 42(2): 128-134. DOI: 10.19591/j.cnki.cn11-1974/tf.2021100013
Citation: DING Xiaolong, YANG Zhaofang, ZHENG Hejing. Effect of ZrP on properties of CuBi-steel-backed double-layer metal composites[J]. Powder Metallurgy Technology, 2024, 42(2): 128-134. DOI: 10.19591/j.cnki.cn11-1974/tf.2021100013

Effect of ZrP on properties of CuBi-steel-backed double-layer metal composites

More Information
  • Corresponding author:

    DING Xiaolong, E-mail: dxl_9211@163.com

  • Received Date: November 01, 2021
  • Available Online: January 05, 2022
  • The copper-bismuth (CuBi)-steel-backed double-layer metal composite plates were prepared by the sintering and press-rolling composite technology, the effect of zirconium phosphate (ZrP) on the bonding strength, hardness, and tribological properties of the CuBi-steel-backed composite plates was studied. In the results, the addition of ZrP can effectively improve the anti-friction and wear resistance of the CuBi-steel-backed composite plates and enhance the load-bearing capacity. As the ZrP mass fraction increases, the bonding strength of the CuBi-steel-backed composite plates gradually decreases, and the hardness first increases and then decreases. In the constant speed and load test, compared with the CuBi-steel-backed composite plates without ZrP, the addition of 2% and 4% ZrP by mass can effectively improve the friction and wear resistance of the CuBi-steel-backed composite plates, reduce the friction coefficient of the friction pair, and rise the surface temperature. In the constant-speed variable-load test, the addition of ZrP can significantly improve the frictional bearing capacity of the CuBi-steel-backed double-layer materials. Under the condition of end face oil circulation, the limit PV value (friction pair contact surface pressure × friction linear velocity) of the CuBi-steel-backed composite plates by adding ZrP with the mass fraction 4% reaches 14 MPa∙m∙s‒1, which is about 75% higher than that without ZrP (8 MPa∙m∙s‒1).

  • [1]
    雷沙沙, 刘洪军. 铜基复合材料制备工艺的研究进展. 机械工程材料, 2021, 45(10): 13

    Lei S S, Liu H J. Research progress on the preparation technology of copper-based composite materials. Mater Mech Eng, 2021, 45(10): 13
    [2]
    樊舒凯. 铜基石墨自润滑复合材料界面性能调控及其摩擦学性能研究[学位论文]. 兰州: 兰州理工大学, 2021

    Fan S K. Study on the Control of Interface Performance and Tribological Properties of Copper-Based Graphite Self-Lubricating Composites [Dissertation]. Lanzhou: Lanzhou University of Technology, 2021
    [3]
    Mushtaq S, Wani M F. Self-lubricating tribological characterization of lead free Fe‒Cu based plain bearing material. J Tribol, 2017, 12: 18
    [4]
    尹延国, 林福东. 无铅的铜铋轴承材料摩擦学特性研究. 金属功能材料, 2010, 17(5): 5

    Yin Y G, Lin F D. Study on tribological characteristics of lead-free copper bismuth bearing materials. Met Funct Mater, 2010, 17(5): 5
    [5]
    Zhang K Y, Yin Y G, Zhang G T, et al. Tribological properties of FeS‒Cu copper-based self-lubricating bearing materials prepared by mechanical alloying. Tribol Trans, 2020, 63(2): 197 DOI: 10.1080/10402004.2019.1668515
    [6]
    方小亮, 郑合静. 铜基粉末冶金摩擦材料的应用及展望. 粉末冶金技术, 2020, 38(4): 313

    Fang X L, Zheng H J. Application and prospect of copper-based powder metallurgy friction materials. Powder Metall Technol, 2020, 38(4): 313
    [7]
    郑合静, 杨兆方, 丁晓龙, 等. 层状α–磷酸锆改性聚四氟乙烯摩擦磨损性能. 工程塑料应用, 2021, 49(11): 126

    Zheng H J, Yang Z F, Ding X L, et al. Friction and wear properties of layered α-zirconium phosphate modified polytetrafluoroethylene. Eng Plast Appl, 2021, 49(11): 126
    [8]
    李佳欣, 赖学军, 叶振兴, 等. 层状纳米磷酸锆的制备及催化成炭阻燃聚合物的研究进展. 高分子材料科学与工程, 2019, 35(1): 183

    Li J X, Lai X J, Ye Z X, et al. Progress in preparation of nano-layered phosphate zirconium and its catalyzing carbonization in flame retardant polymer. Polym Mater Sci Eng, 2019, 35(1): 183
    [9]
    代莹静, 牛文星, 张效胜, 等. 层状磷酸锆作为润滑脂添加剂的摩擦性能. 石油学报(石油加工), 2018, 34(4): 776

    Dai Y J, Niu W X, Zhang X S, et al. Tribological properties of layered zirconium phosphate as a grease additive. Acta Pet Sinica (Pet Process Ind), 2018, 34(4): 776
    [10]
    Xiao H, Liu S. Zirconium phosphate (ZrP)-based functional materials: Synthesis, properties and applications. Mater Des, 2018, 155: 19 DOI: 10.1016/j.matdes.2018.05.041
    [11]
    尹延国, 唐红跃, 焦明华, 等. 无铅含镍铜-钢双金属轴承材料的摩擦学特性. 中国有色金属学报, 2017(6): 1189

    Yin Y G, Tang H Y, Jiao M H, et al. Tribological properties of lead-free nickel-containing copper-steel bimetallic bearing materials. Chin J Nonferrous Met, 2017(6): 1189
    [12]
    王立全, 张向军, 张斌, 等. 摩擦条件对铜基粉末冶金材料摩擦磨损性能影响的研究. 热加工工艺, 2020, 49(18): 26

    Wang L Q, Zhang X J, Zhang B, et al. Research on the influence of friction conditions on the friction and wear properties of copper-based powder metallurgy materials. Hot Working Technol, 2020, 49(18): 26
    [13]
    Torres H, Rodríguez R M, Prakash B. Tribological behaviour of self-lubricating materials at high temperatures. Int Mater Rev, 2018, 63(5): 309 DOI: 10.1080/09506608.2017.1410944
    [14]
    胡铮, 张楠, 张万昊, 等. 石墨含量对铜基摩擦材料摩擦磨损性能的影响. 粉末冶金技术, 2020, 38(6): 409

    Hu Z, Zhang N, Zhang W H, et al. The influence of graphite content on the friction and wear properties of copper-based friction materials. Powder Metall Technol, 2020, 38(6): 409
    [15]
    武志涛, 侯凯明, 王金清, 等. α-ZrP层状纳米片的修饰改性及其摩擦学性能. 摩擦学学报, 2020(1): 89

    Wu Z T, Hou K M, Wang J Q, et al. Modification and tribological properties of α-ZrP layered nanosheets. Chin J Tribol, 2020(1): 89
    [16]
    王静轩, 王嘉棋, 尹延国, 等. FeS/Cu-Bi铜基滑动轴承材料的干摩擦特性. 轴承, 2020(3): 39 DOI: 10.19533/j.issn1000-3762.2020.03.010

    Wang J X, Wang J Q, Yin Y G, et al. Dry friction characteristics of FeS/Cu‒Bi copper-based sliding bearing materials. Bearings, 2020(3): 39 DOI: 10.19533/j.issn1000-3762.2020.03.010
  • Related Articles

    [1]WANG Lei, GAO Jinchang, BAO Xiaogang, LIN Wanming, GUO Ruipeng. Effects of mechanical milling on microstructure and tensile properties of CoCrFeMnNi high-entropy alloys produced by spark plasma sintering[J]. Powder Metallurgy Technology, 2024, 42(6): 645-651. DOI: 10.19591/j.cnki.cn11-1974/tf.2023010001
    [2]ZHONG Tao, GUO Rongzhen, LIN Xiaochuan, LIU Longting, WANG Jiaxin, XU Zhiqiang, GUO Shibo. Effect of plasma sintering process on the mechanical properties of WC/Cr3C2/La2O3 cutting tool materials[J]. Powder Metallurgy Technology, 2024, 42(6): 582-588. DOI: 10.19591/j.cnki.cn11-1974/tf.2024040013
    [3]LI Yuanyuan, WU Ying, PAN Xiaoqiang, LIU Tingwei. Preparation of boron carbide stainless steel composites by spark plasma sintering[J]. Powder Metallurgy Technology, 2024, 42(4): 381-387. DOI: 10.19591/j.cnki.cn11-1974/tf.2023100003
    [4]WANG Na, WU Zhou, ZHU Qi, XI Sha, ZHANG Xiao, ZHOU Sha, LI Jing, WANG Yuqing. Preparation of Mo–Ni alloys by spark plasma sintering[J]. Powder Metallurgy Technology, 2024, 42(4): 361-366. DOI: 10.19591/j.cnki.cn11-1974/tf.2023030015
    [5]WANG Bin, CHEN Ruizhi, LI Jianfeng, CHEN Pengqi, CHENG Jigui. Preparation of binderless SiCw/WC cemented carbides by spark plasma sintering[J]. Powder Metallurgy Technology, 2023, 41(1): 38-43. DOI: 10.19591/j.cnki.cn11-1974/tf.2022050012
    [6]Fe50Mn30Co10Cr10-xNbC high-entropy alloy composites prepared by SPS technology and characterization of properties[J]. Powder Metallurgy Technology. DOI: 10.19591/j.cnki.cn11-1974/tf.2023010004
    [7]YAN Xing-heng, ZHOU Xin-gui, WANG Hong-lei. Research progress of B4C prepared by spark plasma sintering[J]. Powder Metallurgy Technology, 2022, 40(6): 516-526. DOI: 10.19591/j.cnki.cn11-1974/tf.2020070001
    [8]WU Xiao-jun. Preparation parameter optimization and mechanical properties of the graphene-reinforced TC11 titanium alloys prepared by spark plasma sintering used for engine[J]. Powder Metallurgy Technology, 2022, 40(4): 291-295. DOI: 10.19591/j.cnki.cn11-1974/tf.2020110010
    [9]SHEN Dan-ni, WANG Chao-ning, GAO Peng, KONG Jian. Ultrafine grained W–Ti alloys prepared by spark plasma sintering[J]. Powder Metallurgy Technology, 2021, 39(2): 165-171. DOI: 10.19591/j.cnki.cn11-1974/tf.2019110008
    [10]DENG Lin, JIANG Li-hua. Microstructure and mechanical properties of Ti-21.5Nb alloy prepared by powder sintering used for internal combustion engine[J]. Powder Metallurgy Technology, 2020, 38(3): 201-205. DOI: 10.19591/j.cnki.cn11-1974/tf.2020.03.006

Catalog

    Article Metrics

    Article views (787) PDF downloads (29) Cited by()
    Related

    /

    DownLoad:  Full-Size Img  PowerPoint
    Return
    Return